Catalogo Vega Cutting Tools 2022

FORATURA VEGA CUTTING TOOLS 2022 308 )ZWJ__F 'WNSJQQ (HB) 'RADO 6ELOCITÍ DI TAGLIO Vc m/min !VANZAMENTO FN MM R )NSERTO &ORATURA DIA MM P I C 25.00-43.00 43.01-65.00 '! 125 AP301U(N) 70-130 0.11-0.41 0.14-0.45 '! 125 70-130 0.11-0.41 0.14-0.45 '! 150 70-130 0.11-0.41 0.14-0.45 '! 170 70-130 0.11-0.41 0.14-0.45 Carbon tool steel 210 AP301U(N) 70-120 0.11-0.41 0.20-0.45 Non-Hardened 180 AP301U(N) 55-110 0.11-0.41 0.20-0.45 Tempered 275 70-120 0.11-0.41 0.20-0.45 Tempered 350 70-120 0.11-0.41 0.20-0.45 Annealed 200 AP301U(N) 55-110 0.11-0.38 0.20-0.40 Hardened tool steel 325 55-110 0.20-0.38 0.20-0.40 Non-alloyed steel 180 AP301U(N) 55-110 0.11-0.41 0.20-0.45 Low-alloyalloy<5%) 200 55-110 0.11-0.41 0.20-0.45 Non-Hardened/Ferritic/martensitic 200 AP301U(N) 40-110 0.11-0.41 0.20-0.45 Austenitic 200 40-110 0.11-0.41 0.20-0.45 Austenitic, precipitation hardened (PH) 300 40-110 0.11-0.33 0.20-0.35 Austenitic/ferritic, duplex 230 40-80 0.11-0.33 0.20-0.35 Ferritic 200 AP301U(N) 80-120 0.11-0.38 0.24-0.41 Pearlitic 260 80-120 0.11-0.38 0.24-0.41 Low tensile strength 180 AP301U(N) 60-110 0.11-0.38 0.24-0.41 High tensile strength 245 60-110 0.11-0.38 0.24-0.41 Ferritic 160 AP301U(N) 50-110 0.11-0.38 0.24-0.41 Pearlitic 250 50-110 0.11-0.38 0.24-0.41 GGV (CGI) 230 non-aging 30 AP301U(N) 65-150 0.09-0.33 0.20-0.33 aged 100 65-150 0.09-0.33 0.20-0.33 Ƶ 7M RSR EKMRK 75 AP301U(N) 65-150 0.09-0.33 0.20-0.33 Ƶ 7M EKIH 90 65-150 0.09-0.33 0.20-0.33 > 12% Si, non-aging 130 65-150 0.09-0.33 0.20-0.33 70 Unalloyed, electrolytic copper 100 AP301U(N) 65-150 0.09-0.33 0.20-0.33 Brass, bronze, red brass 90 65-150 0.09-0.33 0.20-0.33 Cu alloys, short-chip 110 65-150 0.09-0.33 0.20-0.33 High tensile, Ampco alloy 300 65-150 0.09-0.33 0.20-0.33 Fe-based annealed 200 AP301U(N) 10-55 0.09-0.30 0.20-0.33 Fe-based hardened 280 10-55 0.09-0.30 0.20-0.33 Ni or Co-based annealed 250 10-55 0.09-0.30 0.20-0.33 Ni or Co-based hardened 350 10-55 0.09-0.30 0.20-0.33 Ni or Co-based cast 320 10-55 0.09-0.30 0.20-0.33 Pure titanium 200 AP301U(N) 30-60 0.09-0.30 0.20-0.33 » EPPS]W 375 30-60 0.09-0.30 0.20-0.33 » ERH ¼ EPPS]W 375 30-60 0.09-0.30 0.20-0.33 ¼ EPPS]W 410 30-60 0.09-0.30 0.20-0.33 Hardened and tempered 43-47 HRC 47-60 HRC 5FWFRJYWN IN YFLQNT HTSXNLQNFYN (Dia 25.00-65.00mm) P M K S N H *) Insert position-P , I , C 4!TIVMTLIVEP MRWIVX -!MRXIVQIHMEXI MRWIVX '!GIRXIV MRWIVX 2FYJWNFQN IF QF[TWFWJ &HHNFNT STS QJLFYT &HHNFNT FQ HFWGTSNT &HHNFNT GFXXTQJLFYT &HHNFNT FQYTQJLFYT &HHNFNT KZXT &HHNFNT NSTXXNIFGNQJ ,MNXF RFQQJFGNQJ ,MNXF LWNLNF ,MNXF STIZQFWJ 1JLMJ IN FQQZRNSNT QF[TWFYT 1JLMJ IN FQQZRNSNT KZXJ 1JLMJ IN RFLSJXNT 7FRJ J QJLMJ IN WFRJ GWTS_T TYYTSJ 1JLMJ WJXNXYJSYN FQ HFQTWJ 1JLMJ IN 9NYFSNT &HHNFNT YJRUWFYT ,MNXF YJRUWFYF A FISSAGGIO MECCANICO ACHTECK

Made with FlippingBook

RkJQdWJsaXNoZXIy NjU1MTUz