FORATURA www.vegaonline.net info@vegaonline.net 309 2FYJWNFQN IF QF[TWFWJ )ZWJ__F 'WNSJQQ (HB) 'RADO 6ELOCITÍ DI TAGLIO Vc m/min !VANZAMENTO FN MM R )NSERTO &ORATURA DIA MM P I C 63.50 &HHNFNT STS QJLFYT '! 125 AP301U(N) 80-100 0.18-0.35 '! 125 80-100 0.18-0.35 '! 150 80-100 0.18-0.35 '! 170 80-100 0.18-0.35 &HHNFNT FQ HFWGTSNT Carbon tool steel 210 AP301U(N) 70-100 0.18-0.35 &HHNFNT GFXXTQJLFYT Non-Hardened 180 AP301U(N) 60-100 0.16-0.35 Tempered 275 70-100 0.18-0.30 Tempered 350 70-100 0.18-0.30 &HHNFNT FQYTQJLFYT Annealed 200 AP301U(N) 60-100 0.16-0.30 Hardened tool steel 325 60-100 0.16-0.30 &HHNFNT KZXT Non-alloyed steel 180 AP301U(N) 50-100 0.15-0.30 Low-alloy alloy<5%) 200 50-100 0.15-0.30 &HHNFNT NSTXXNIFGNQJ Non-Hardened/Ferritic/martensitic 200 AP301U(N) 50-90 0.16-0.35 Austenitic 200 50-90 0.16-0.35 Austenitic, precipitation hardened (PH) 300 Austenitic/ferritic, duplex 230 ,MNXF RFQQJFGNQJ Ferritic 200 AP301U(N) Pearlitic 260 ,MNXF LWNLNF Low tensile strength 180 AP301U(N) High tensile strength 245 ,MNXF STIZQFWJ Ferritic 160 AP301U(N) Pearlitic 250 GGV (CGI) 230 1JLMJ IN FQQZRNSNT QF[TWFYT non-aging 30 AP301U(N) 65-130 0.10-0.30 aged 100 65-130 0.10-0.30 1JLMJ IN FQQZRNSNT KZXJ Ƶ 7M RSR EKMRK 75 AP301U(N) 65-130 0.10-0.30 Ƶ 7M EKIH 90 65-130 0.10-0.30 > 12% Si, non-aging 130 65-130 0.10-0.30 1JLMJ IN RFLSJXNT 70 7FRJ J QJLMJ IN WFRJ GWTS_T TYYTSJ Unalloyed, electrolytic copper 100 AP301U(N) 65-130 0.10-0.30 Brass, bronze, red brass 90 65-130 0.10-0.30 Cu alloys, short-chip 110 65-130 0.10-0.30 High tensile, Ampco alloy 300 65-130 0.10-0.30 1JLMJ WJXNXYJSYN FQ HFQTWJ Fe-based annealed 200 AP301U(N) 20-65 0.15-0.30 Fe-based hardened 280 20-65 0.15-0.30 Ni or Co-based annealed 250 20-65 0.15-0.30 Ni or Co-based hardened 350 20-65 0.15-0.30 Ni or Co-based cast 320 1JLMJ IN 9NYFSNT Pure titanium 200 AP301U(N) 30-100 0.15-0.30 » EPPS]W 375 30-100 0.15-0.30 » ERH ¼ EPPS]W 375 30-100 0.15-0.30 ¼ EPPS]W 410 30-100 0.15-0.30 &HHNFNT YJRUWFYT Hardened and tempered 43-47 HRC ,MNXF YJRUWFYF 47-60 HRC 5FWFRJYWN IN YFLQNT HTSXNLQNFYN (ME ƶ QQ P M K S N H *) Insert position-P , I , C 4!TIVMTLIVEP MRWIVX -!MRXIVQIHMEXI MRWIVX '!GIRXIV MRWIVX ACHTECK A FISSAGGIO MECCANICO
RkJQdWJsaXNoZXIy NjU1MTUz